WALL RECESSED INSECT LIGHT TRAPS

ADA - Designed to Comply With the Americans with Disabilities Act

Designed to comply with the American with Disability Act (the ADA), Insect-O-Cutor's recess mounted insect light traps (ILT) offer a mechanical pest control option for facilities concerned with flying insects and ADA compliance.

Electronic fly killer (EFK) series 18204E and 36204E are powered by electronic-ballasted circuitry that converts normal 60 Hertz line current to 25 kHz… for increased operational efficiency — resulting in an 8% to 15% increase in light output.

The safety guard has slightly larger, overlapping dimensions than the unit. The vertically beveled guard abuts firmly to the wall surface. Note: the wall recessed body is in aluminized steel metal material.

Installation: For stability, the body of this insect light trap should rest atop a permanent cross-brace/platform secured horizontally within the wall opening. The unit body may be adjusted forward or backward upon brace/platform to accommodate proper wall depth. Convenient side holes allow access to a wall stud/support. Keyhole slots on the back of this electronic fly killer allow for securing to a rear surface.

Series 18204E

Series 18204E

Click on Image
to Enlarge

Series 18204E Insect Light Traps
(Not available in Canada)

Series 18204E
 Energy Efficient Model Numbers
Metal Finish 
Beige Textured18204EDGR
Aluminized Steel18204EDGAR
Stainless Steel18204EDGSR
Black Light Lamps18 BL Unfiltered and 18B BLB Filtered
Gross Weight of
Specific Models
Beige Textured = 25 lb / 11.3 kg
Aluminized Steel = 25 lb / 11.3 kg
Stainless Steel = 28 lb / 12.7 kg
Dimensions of Wall
Recessed Unit
13.0" Wide X 28.5" High X 4.125" Deep
Dimensions of Safety Guard14.5" Wide X 29.875" High
Series 36204E

Series 36204E

Click on Image
to Enlarge

Series 36204E Insect Light Traps
(Not available in Canada)

Series 36204E
 Energy Efficient Model Numbers
Metal Finish 
Beige Textured36204EDGR
Aluminized Steel36204EDGAR
Stainless Steel36204EDGSR
Black Light Lamps36 BL Unfiltered and 36B BLB Filtered
Gross Weight of
Specific Models
Beige Textured = 47 lb / 21.3 kg
Aluminized Steel = 47 lb / 21.3 kg
Stainless Steel = 53 lb / 24.1 kg
Dimensions of Wall
Recessed Unit
13.0" Wide X 46.5" High X 4.125" Deep
Dimensions of Safety Guard14.5" Wide X 47.875" High






Design Features of the Wall Recessed Insect Light Trap: The three-wire grounded cord and plug is positioned on top of unit to ensure trouble-free recessing. Tamper-resistant safety guard affixed by four removable screws. Internal metal insect collection drawer; wraparound reflector panel behind electric grid to increase black light emission; spring-loaded and fixed lampholder sets for simple lamp installation and replacement.


Insect-O-Cutor® Insect Light Traps

For use in areas where low life time cost insect light traps are preferred. Our wide range of models provides a variety of choice for almost any area within your facility … from warehouse load docks … to production areas … to labs … to even office areas. Insect-O-Cutor® insect light traps and glueboard flytraps incorporate state-of-the-art, energy-efficient components and black light insect attraction lamps that meet our stringent criteria.

Energy-efficient models are designed to comply with various energy conservation programs (LEED, Green-lights, EPACT). Electronic-ballasted units reduce overall electrical consumption while actually increasing light output by 8% to 15% per lamp due to increased operational efficiency. Less energy consumed … more insect attraction light emitted.

High performance ILT models, now discontinued, utilized ultra-high current circuitry to increase insect attracting black light emission. An Insect-O-Cutor® innovation, ultra-high current circuitry over-drove insect attraction lamps without shortening lamp life.

ALSO SEE: INSECT-O-CUTOR SYSTEM DESIGN